1800 Series Submersible Pressure Level Sensor Platform - ACCESSORIES

1800 Series Submersible Pressure Level Sensor Platform - ACCESSORIES
by Druck

Please consider these optional accessories:

Druck SO1830E
 Druck - ACCESSORY PACK for 1800 Series Submersible Pressure Sensors (P/N: SO1830E)

This accessory pack includes an STE box, cable clamp, slimline sink weight and a direct calibration adapter for the Druck 1800 Series Submersible Pressure Sensor Platform (PTX1830/1835/1840/1845, PDCR1830/1840).

$300.00
Druck - Sensor Termination Enclosure (P/N: 202-034-05)
 		Druck - Sensor Termination Enclosure (P/N: 202-034-05)
Simple field termination for vented gauge pressure transducers and transmitters.
Prevents water damage caused by moisture or high humidity from forming inside vented gauge pressure sensors.		 $182.00
Druck - Dri-Can Desiccant Pack (P/N: 600-914)
Druck - Dri-Can Desiccant Pack (P/N: 600-914)
Indicates when the desiccant is OK or used. When the color is blue, the desiccant is OK; when it is red, it is time to be replaced. Under normal conditions, the desiccant should be changed every 6 to 12 months.
$29.30
In-Situ - Baro TROLL Barometric Pressure Data Logger and Sensor

In-Situ - Level BaroTROLL - Precision Pressure Barometer

Barometric Pressure Sensor for use with the 1800 Series Submersible Pressure Sensor:

  • Titanium construction
  • Outputs: 4-20 mA, SDI-12, or ModBus
  • Sub-1 inch diameter for easy fit
  • NIST calibration report
  • Accuracy: +/-0.05 FS from -5 to 50° C (23 to 122° F)
  • Can be used effectively over 3.5 square mile area and altitude delta of 350 feet with negligible effect on correction factor accuracy (subtracting the barometric reading from an absolute submersible pressure sensor)..

ELIMINATES THE NEED FOR USING AN STE BOX (PLEASE NOTE: When you specify your submersible pressure sensor to use the absolute pressure reference, you can use a barometer to subtract out the barometric pressure to get you to gauge pressure. This eliminates the need to use a desiccant box.

Starting at:

$874.50
Druck - PTX Cable Clamp (P/N: 192-373-01)
 Druck - PTX Cable Clamp (P/N: 192-373-01)
Cable Clamp, fits all Druck Submersible Pressure Level Sensor Cable (1800 Series, UNIK5000, and etc.).		 $49.60
Druck - Sinkweights for 1800 Series, 17.5 mm Diameter (P/N: 222-116-01 and DA2608-1-01)
Druck - Sinkweights for 1800 Series (P/N: DA2608-1-01 and DA4068-1-01)
Sinkweights for Druck 1800 Series Submersible Sensors. Available in two lengths, long and short.

Starting at:

$79.90
Druck - Calibration Adaptors for 17.5 mm Diameter Pressure Sensors

Druck - Calibration Adaptors for 17.5 mm Diameter Pressure Sensors

For use with the Druck 1800 Series Submersible Pressure Sensor Platform (PTX1830/1835/1840/1845, PDCR1830/1840).

The female side of the adaptor is M14 x 1.5 mm-Female, which screws onto the standard pressure port on an 1800 Series Submersible Pressure Sensor (with nose cone removed). The male side of the adaptor is G1/8.

Starting at:

$66.70

Druck - Nose Cone for 1800 Series Submersible Pressure Level Sensors (P/N: 222-127-01)

Protects the sensor tip from damage. Made of Delrin® plastic for durability.

 $26.70
Electro-Numerics - Micro Series 1/8 DIN Digital Process Meter

The panel meter supplies power to your pressure sensor, and has options for signal re-transmission, output relays, digital interfaces and more. Impressive Update Rate for the Micro-P: 60 times per second to the display, and retransmission update rate is 56 times per second (for 60 herz operation). Meter operates on AC power from 85 to 264Vac.
Starting at: $118.00